FAA-PMA STEARMAN CLAMPS
These clamps are formed from annealed aluminum and then heat treated. This process is how the original clamps were manufactured.
YAS-106-D51 Clamp 3/4" Tube Aluminum 18.95 ea
1 lower bird cage brace.
YAS-107-D51 Clamp 7/8" Tube Aluminum 18.95 ea
8 bird cage, 1 oil line support.
YAS-108-D51 Clamp 1" Tube Aluminum 18.95 ea
6 floor boards, 4 data case back of seat,
2 battery tray, 2 front trim tab control,
2 oil line support.
YAS-108-D64 Clamp 1" Tube Aluminum 18.95 ea
1 air intake to mount, 2 fuel valve bracket,
2 fuel sump bracket, 2 front dash panel.
YAS-109-D51 Clamp 1-1/8" Tube Aluminum 18.95 ea
9 bird cage, 3 rear trim tab control,
2 floor boards, 2 battery tray.
YAS-109-D64 Clamp 1-1/8" Tube Aluminum 18.95 ea
2 rear dash panel.
YAS-110-D51 Clamp 1-1/4" Tube Aluminum 18.95 ea
2 bird cage, 4 rear of cockpit bulkheads,
2 carb heat control,4 front trim control plate,
2 floor boards.
FAA-PMA STEARMAN BATTERY TRAYS
These trays are formed and heat treated just like the originals. The tray is configured for the standard 35 amp aircraft battery.
YA-A75N1-3917 299.95 ea
FAA-PMA STEARMAN BATTERY HOLD DOWN STUD
Machined tool cut threads and Cadmium plated. Two required per airplane.
YA-A75N1-3919 19.95 ea
FAA-PMA STEARMAN SEAT SPRINGS
Two Required Per Seat
YA-E75N1-3602 45.00 ea
FAA-PMA Wing and Horizontal Inner Inspection Ring
This part is riveted to the horizonal stabilizer and glued into the fabric on the upper and lower wings. 14 are used on the wings and 2 on the horizontal.
YA75-118 39.95 ea
FAA-PMA Outer Inspection Window Frame
This frame is used on both wings and the horizontal stabilizer. 2 required for the horizontal, 2 required per upper wing, and 5 per lower wing.
YA75-1117 18.50 ea
FAA-PMA Wing Inspection Window
These clear windows are used on both the upper and lower wings.
YA75-1119 15.50 ea
FAA-PMA Horizontal Stabilizer Inspection Window
These clear windows are used on the horizontal. 2 required.
YA75-1727 21.00 ea
FAA-PMA Dzus Bracket Lower Wing (Front)
Used on lower wings at the front for the wing attach bolt inspection door. These brackets are formed and heat treated as originally manufactured. 1 required per wing.
YA75-2404 34.95 ea
FAA-PMA Dzus Bracket Lower Wing (Rear)
Used on the bottom of the lower wings at the long narrow door for the rear wing attach bolt. These brackets are formed and heat treated as originally manufactured. 2 required per wing.
YA75-1276 34.95 ea
FAA-PMA Dzus Bracket Airframe
Used on front of birdcage, firewall, etc. These brackets are formed and heat treated as originally manufactured. 24 required per airplane.
YA75-2416 34.95 ea
FAA-PMA Bulkhead Fuselage Side Cowl Support
Used just behind the landing gear ahead of the lower wing. These bulkheads and Dzus brackets are formed and heat treated just as the originals.
YA75-2341 Left Hand 249.95 ea
YA75-2341-1 Right Hand 249.95 ea
FAA-PMA Fire Extinguisher Door
YA75-2376 Arch, Fire Extinguisher Frame Support 50.00 ea
YA75-2399-T Top Fire Door Support Drilled (with nut plates installed) 149.95 ea
YA75-2399-B Bottom Fire Door Support Drilled (with nut plates installed) 149.95 ea
YA75-2365 Fire Door Arch Reinforcement (2 required) 50.00 ea
YA75-2387 Frame Fire Extinguisher Door 149.95 ea
YA75-3631-KIT Kit includes above parts in quantity needed 1230.00 kit
YA75-3642 Spring, Fire Door Handle (2 required) 13.00 ea
FAA-PMA Aileron Control Stop Bolt
Two required per airplane.
YAS-106-D51 15.00 ea
FAA-PMA Elevator Control Stop Bolt
Two required per airplane.
YA75-3326-1 15.00 ea
FAA-PMA Elevator Push-Pull Tube Control Fork Bushing
These have been thoroughly tested for the correct rubber composition as specified by the original Boeing prints using a specialized tool that measures deflection under force. Two required per airplane.
YA75-3328 99.95 ea
FAA-PMA STEARMAN CLAMPS
These clamps are formed from annealed aluminum and then heat treated. This process is how the original clamps were manufactured.
YAS-106-D51 Clamp 3/4" Tube Aluminum 18.95 ea
FAA-PMA STEARMAN CLAMPS
These clamps are formed from annealed aluminum and then heat treated. This process is how the original clamps were manufactured.
YAS-106-D51 Clamp 3/4" Tube Aluminum 18.95 ea
FAA-PMA STEARMAN CLAMPS
These clamps are formed from annealed aluminum and then heat treated. This process is how the original clamps were manufactured.
YAS-106-D51 Clamp 3/4" Tube Aluminum 18.95 ea
FAA-PMA STEARMAN CLAMPS
These clamps are formed from annealed aluminum and then heat treated. This process is how the original clamps were manufactured.
YAS-106-D51 Clamp 3/4" Tube Aluminum 18.95 ea